Rancang Bangun Mesin Pemisah Kerupuk Mawar Guna Meningkatkan Output Pada Proses Pemisahan Kerupuk
Main Article Content
Abstract
Mr Rizal's MSME is located in Jerukgamping Village, Krian Sub-District, Sidoarjo Regency, East Java, processing the production of rose crackers from raw goods to finished products takes a maximum of 1 day and a maximum of 2 days. This is because there is a drying process that still relies on the sun's heat. The separation process Crackers that are done manually result in the resulting output not being optimal because the process takes quite a long time so it cannot be finished on the same day and must be continued the next morning. With the problems that occur in Mr. Rizal's cracker MSMEs, the researcher provides a solution to speed up the process of separating crackers that are still stuck to each other and only requires 1 worker. The solution used for the problems that exist in Mr. Rızal's rose cracker MSMEs is to carry out anthropometric and percentile calculations. which is used to determine the dimensions of the rose cracker separating machine. The cracker separating machine is designed using dimensions from anthropometry and the 50th percentile of workers so that it can be seen that the height of the machine frame is 103.5 cm, the diameter of the cracker separating tube is 67.25 cm, the height of the cracker exit path is 92.9 cm after it is done. In the experiment there was a comparison of the output of crackers that had been separated. The output before design was 113.5 kg, requiring 200 minutes with an output per minute of 0.6 kg. Meanwhile, the output after design was 150 kg, requiring 60 minutes with an output per minute of 2.5 kg.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
E. P. Putri, “"Penyuluhan Strategi Pengembangan Bisnis Umkm Desa Minggirsari, Kecamatan Kanigoro, Kabupaten Blitar, Provinsi Jawa Timur,” PSHPM Pros. Semin. Has. Kegiat. Pengabdi. Masyarakat., vol. Vol 1 No 1, 2022.
S. Wignjosoebroto, Ergonomi Studi Gerak dan Waktu. Surabaya: Prima Printing, 2006.
N. Yanto ; Billy, Ergonomi dasar dasar studi waktu dan gerak untuk menganalisis dan perbaikan sistem kerja. Jakarta, 2017.
H. F. Khotib, Mohammad ; Satoto, “Perancangan Alat Pembentuk Pasak Perahu Dengan Pendekatan Ergonomi Guna Meningkatkan Produktivitas,” Teknika, vol. Vol 1 No 1, pp. 165–172, 2023.
Nugroho;Nurwidiah Sulistyo; Erni Puspanantasari Putri, “"Upaya Menurunkan Kegagalan Proses Pengemasan Margarin di PT. Smart Tbk Surabaya,” J. Serambi Eng., vol. 8.4, 2023.
H. ; S. ; O. R. Murnawan, “Reenggineering produksi pegangan rantang soto guna meningkatkan produktivitas pembuatan rantang soto di UD. Gadjah Delta,” Teknika, vol. Vol1 No 1, pp. 50–60, 2023.
E. Adji Hadisaputra, Sasongko; Puspanantasari putri, “Penentuan Jumlah Tenaga Kerja Guna Meningkatkan Produktifitas pada Bagian Produksi UD.Redline,” J. Tek. Ind. Terintegrasi, vol. 7, no. 1, pp. 67–73, 2024.
R. M. Barnes, Motion and time studi design and measurment of work. New York: John wiley & son, 1980.
J. Hutabarat, Dasar Dasar Pengetahuan Ergonomi. Malang: Media Nusa Creative, 2017.
R. Ginting, Perancangan Produk. Medan: Graha Ilmu, 2009.
I. Rahmaniyah, Astuti : Iftadi, Analisis dan Perancangan Sistem Kerja. Surakarta: Grup Penerbit CV Budi Utama, 2016.
P. E. D. K. Safik, Moch ; Wati, “Perancangan Ulang Alat Angkut Guna Menurunkan Ongkos Material Handling,” Semin. dan Konf. Nas. IDEC, pp. 1–9, 2022.
H. Murnawan, “Rancang Bangun Tungku Peleburan Logam Alumunium Berbahan Bakar Oli Bekas Untuk Menekan Biaya Produksi Guna Memiliki Kemampuan Dan Daya Saing Di Pasar,” JPM17 J. Pengabdi. Masy. 7.1, pp. 9–16, 2022.
H. Wati, Putu Eka Dewi Karunia ; Murnawan, “Perancangan Alat Pembuat Mata Pisau Mesin Pemotong Singkong Dengan Memperhatikan Aspek Ergonomi,” J. Sist. Intergasi Ind., vol. Vol 9 No 1, pp. 60–68, 2022.
I. N. Yuwono, Istantyo ; Arief Zainal ; Harijanto ; Djoko, Setijanen;Singgih Mochamamad ; Lokajaya, “Desain dan Pengadaan Meja Multiguna untuk Kuliner Makanan Bu Lilik Secara Ergonomis,” Adipati, vol. Vol 2 No 1, pp. 37–43, 2023