Proses Painting dan Pengukuran Ketebalan Cat Pada Kabin Mobil Type Dutro Dump 130 HD X-POWER di PT. XYZ

Main Article Content

Aang Iryadi
Rizal Hanifi
Kardiman
Viktor Naubnome

Abstract

The process of painting a car cabin at PT XYZ, a leading automotive company in Indonesia, involves a series of structured and rigorous steps to ensure optimal paint quality before the vehicle leaves the manufacturing facility. The painting process involves a series of structured stages, starting from surface preparation to application of paint layers. Paint thickness measurements are carried out to ensure that the thickness of the paint layer complies with established standards for optimal protection and aesthetics. It was found that the company implemented advanced technologies such as electrodeposition (ED) to ensure an even and long-lasting paint layer. Apart from that, implementing grounding safety and the Quality Gate process is key in maintaining safety, quality and customer satisfaction.

Article Details

How to Cite
[1]
A. I., Rizal Hanifi, Kardiman, and Viktor Naubnome, “Proses Painting dan Pengukuran Ketebalan Cat Pada Kabin Mobil Type Dutro Dump 130 HD X-POWER di PT. XYZ”, JSE, vol. 9, no. 3, Jul. 2024.
Section
Articles

References

F. Julian, N. Fauji, M. Universitas Singaperbangsa Karawang, and D. Fakultas Teknik Universitas Singaperbangsa Karawang, “Sistem Pengendalian Kualitas (Quality Control) Pada Proses Fabrikasi Project ‘Refinery Development Master Plan (RDMP)’’’,’” J. Ilm. Wahana Pendidik., vol. 8, no. 15, pp. 228–237, 2022.

A. Adyatama and N. U. Handayani, “Perbaikan Kualitas Menggunakan Prinsip Kaizen Dan 5 Why Analysis: Studi Kasus Pada Painting Shop Karawang Plant 1, Pt Toyota Motor Manufacturing Indonesia,” J@ti Undip J. Tek. Ind., vol. 13, no. 3, p. 169, 2018.

S A. Lawi, “Optimization of Chemical Pretreatment Process by Using Design of Experiment for Metal Surface Prior Painting,” Profisiensi, vol. 5, no. 2, pp. 69–80, 2017.

H. Kartika, “Penerapan Lean Kaizen untuk Meningkatkan Produktivitas Line Painting pada Bagian Produksi Automotive dengan Metode PDCA,” J. Sist. Tek. Ind., vol. 22, no. 1, pp. 22–32, 2020.

Salman, M. Rahman, S. T. Anda, R. A. Putra, and Miswar, “Utilization of Industrial Wood Scraps in An Effort to Improve the Creative Industry of Calligraphy Art,” ABDIMAS Talent. J. Pengabdi. Kpd. Masy., vol. 8, no. 2, pp. 775–782, 2023.

R. A. Parama, H. Studiawan, and R. J. Akbar, “Implementasi Continuous Integration dan Continuous Delivery Pada Aplikasi myITS Single Sign On,” J. Tek. ITS, vol. 11, no. 3, 2022.

E. Haryanto and B. P. Ichtiarto, “Analisa Penurunan Cacat (Defect) Cat Bintik Debu Dengan Metodologi Six Sigma Pada Proses Painting Produk Fuel Tank di PT. SSO Tangerang,” J. Pasti, vol. 13, no. 3, p. 326, 2020.

G. Vourlias, N. Pistofidis, E. L. Pavlidou, G. Stergioudis, and E. K. Polychroniadis, “Study of the structure of hot-dip galvanizing byproducts,” J. Optoelectron. Adv. Mater., vol. 9, no. 9, pp. 2937–2942, 2007.

A. S. S, A. Warsito, and A. Syakur, “Perancangan Pembangkit Tegangan Tinggi Dc Untuk Proses Powder Coating Secara Elektrostatik,” Transient, no. December 2011, pp. 1–7, 2010.

M. Sofian et al., “Perlindungan Korosi Di Perkapalan,” J. Pendidik. Tek. Mesin, vol. 22, no. 2, pp. 50–56, 20228.

M. Cesyantikha and Wahyudi, “Analisis Pengaruh Perbandingan Campuran Thinner Dengan Varnish Terhadap Kualitas Hasil Pengecatan,” J. Kompetensi Tek., vol. 11, no. 2, pp. 28–33, 2019.

W. S. Annisa Mulia Rani, “Menganalisis Defect Sanding Mark Unit Pick Up Tmc,” JISI (Jurnal Integr. Sist. Ind., vol. 3, no. 1, pp. 15–22, 2016.

Most read articles by the same author(s)