Analisis Kinerja Mesin Grate Cooler Tipe CFG Kapasitas 321 Ton/Jam Pada Proses Produksi Clinker Berdasarkan Efisiensi Thermal

Article Sidebar

PDF
Published: Jul 11, 2024
DOI: https://doi.org/10.32672/jse.v9i3.1911
Keywords:
Pengecatan kabin mobil, electrodeposition (ED), grounding safety, Quality Gate, inovasi teknologi

Main Article Content

Muhammad Adib Arifin
Ratna Dewi Anjani
Program Studi Teknik Mesin, Universitas Singaperbangsa Karawang

Abstract

This research aims to analyze the performance of a CFG type grid cooler in the clinker cooling process with a capacity of 321 tons per hour in the cement industry. The analysis focused on the thermal efficiency of the engine to identify potential operational efficiency improvements. Research methods include heat balance, mass balance measurements and evaluation of heat loss in the cooling process. It is hoped that the results of this research can provide guidance in optimizing the operation of grate cooling machines, improving the quality and energy efficiency of clinker produced in the cement industry.

Article Details

How to Cite
[1]
M. A. A. and Ratna Dewi Anjani, “Analisis Kinerja Mesin Grate Cooler Tipe CFG Kapasitas 321 Ton/Jam Pada Proses Produksi Clinker Berdasarkan Efisiensi Thermal”, JSE, vol. 9, no. 3, Jul. 2024.
Issue
Vol. 9 No. 3 (2024): Juli 2024
Section
Articles
Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

References

R. R. Nur, F. D. Hartanti, and P. Sutikno, “Studi Awal Desain Pabrik Semen Portland dengan Waste Paper Sludge Ash sebagai Bahan Baku Alternatif,” J. Tek. ITS, vol. 4, no. 2, pp. 164–168, 2015.

A. U. Farahdiba and N. S. Yurinda, “Analisis Life Cycle Assessment (Lca) ‘Gate To Grave’ Proses Produksi Semen,” EnviroUS, vol. 2, no. 2, pp. 98–103, 2022.

V. G. A. Kurniawan, “Analisis Persediaan Bahan Baku Pasir Besi Di Pt.Semen Baturaja,” J. Multidisipliner Kapalamada, vol. 1, no. 03, pp. 406–411, 2022.

D. E. Putri and D. Rimantho, “Analisis Pengendalian Kualitas Menggunakan Kapabilitas Proses Produksi Kantong Semen,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 8, no. 1, pp. 35–42, 2022.

M. R. Rahmat, “Perancangan dan Pembuatan Tungku Heat Treatment,” J. Ilm. Tek. Mesin Univ. Islam 45, vol. 3, no. 2, pp. 133–148, 2015.

A. Khoerunnisa, “Analisis Pengendalian Kualitas Produk Hinge AFT dengan Metode Six Sigma di PT X,” J. Surya Tek., vol. 10, no. 1, pp. 547–551, 2023.

E. Amrina, “Evaluasi Keandalan Desain Fresh Air Damper 5J1S02 Dan 5J1S04 Di Pabrik Semen Indarung V,” J. Energy Electr. Eng., vol. 5, no. 2, pp. 94–105, 2024.

. Bagus Prasetiyo, P. Utomo, and A. Sinar Saputro, “Analisis Kegagalan pada Bearing Block Clinker Cooler PT Semen Baturaja Pabrik 2 menggunakan Failure Mode and Effect Analysis Method (FMEA),” J. Mesin Nusant., vol. 6, no. 1, pp. 47–53, 2023.

Putri R.A, Winahju W.S, and Mashuri Muhammad, “Penerapan Metode Ridge Regression danSupport Vector Regression (SVR) untukPrediksi Indeks Batubara di PT XYZ,” J. Sains Dan Seni Its, vol. 9, no. 1, pp. 64–71, 2020.

M. Pratiwi, U. Sriwijaya, and S. L. Development, “Efisiensi Clinker Cooler Di Pt Semen Baturaja (Persero) Tbk,” J. Pengetah. Ilmu Terap. E-IECN, vol. 3, no. 2, pp. 2003–0521, 2022.

T. R. Harjanto, M. Fahrurrozi, and I. Made Bendiyasa, “Life Cycle Assessment Pabrik Semen PT Holcim Indonesia Tbk. Pabrik Cilacap: Komparasi antara Bahan Bakar Batubara dengan Biomassa,” J. Rekayasa Proses, vol. 6, no. 2, p. 51, 2012.

A. Muchtar and A. Fitriati, “Analisis Penerapan Metode Bag Weight Statistics Menggunakan SAP ECC 6 Dan Pengaruh Sistem Kalibrasi Berkala Di Weighbridge Dalam Upaya Mengurangi Terjadinya Over Weight Pada …,” Temat. J. Informatics Inf. Syst., vol. 2, no. 1, pp. 25–30, 2014.

F. A. Ansori, “Perpindahan Panas Clinker pada Grate Cooler di PT Indocement Tunggal Prakarsa Tbk.,” Ilm. Tek. Mesin, vol. 02, no. 02, pp. 18–27, 2022,